PART 4 HOW TO CEILING FAN WIND TURBINE PART 4
THIS IS A VIDEO TO SHOW THOSE WHO DONT WANT TO SPEND A LOT OF MONEY FOR THE BIG SYSTEMS OUT THERE. THE BLACK UNIT IN THE BACK GROUND IS THE ONE THAT IM MAKING FOR A FRIEND WHO WILL USE IT WITH GREAT GLADNESS. HIS ELECTRICAL SYSTEM WAS ALMOST COMPLETELY DESTROYED BY LIGHTENING. IT WOULD COST TOO MUCH FOR REPAIRS AND NEW DEPOSITS AND OLD BILL TO RECONNECT, ESPECIALY WITH REPAIRS FOR A NEW SERVICE BOX AND UPDATING TO A BREAKER SYSTEM AND THE WIRES DESTROYED IN THE HOUSE. ALTHOUGH THIS UNIT WILL NOT NORMALLY SUPPLY A NORMAL HOUSE HOLD IT WILL ALLOW HIM TO HAVE LIGHTS , RADIO, TV , CELLPHONE CHARGING, AND A FEW MORE THINGS BUT NOT ALL AT ONCE OR CONSTANTLY. BUT 20 DOLLARS A DAY FOR GAS IN A GENERATOR IS NOT AN OPTION EITHER. A BAG OF ICE, AND A COOLER IS. WE ARE MAKING A SOLAR HOT WATER HEATER AS WELL. BY 1:00 PM HE WILL HAVE ENOUGH WATER TO DO DISHES AND GET A NICE HOT SHOWER. THEN RELAX BY THE TV OR RADIO FOR A FEW HOURS ON STORED ENERGY. THEN GO TO SLEEP WITH A SMILE. IF HE GETS UP IN THE NIGHT HE CAN JUST TURN ON THE LIGHT. AND ITS ALL FREE. I HAVE ONE CONFESSION TO MAKE ABOUT THE ONE IN THE FIRST VIDEO THAT EVERYONE HAS COMPLEMENTED ON FROM THE BEGINNING. THAT IS , THAT THE ONE THAT IS IN THE VIDEO IS THE 7th OR 8th ONE I DID. I DID IT FOR SOMEONE ELSE BUT I DESTROYED ONE OF THE COIL SETS IN IT BY PULLING ON THE WIRES TO HARD WHILE I WAS RETHREADING THE WIRES TO COME OUT THE OTHER SIDE. BUT THE 12 VOLT SYSTEM INSTEAD OF 24 VOLT SYSTEM WILL NOT SLOW THE BLADES DOWN WHEN UNDER A LOAD SO IT PERFORMS AT ITS LOWERED MAXIMUM VOLTAGE MOST OF THE TIME. IT SEEMS TO KEEP MY SHOP RADIO AND FLOURESENT LIGHT GOING AS MUCH AS I NEED IT TO EXCEPT FOR WHEN IT RAINS AND THE WIND DOESNT BLOW FOR A FEW DAYS. ONE OF THE CEILING FAN MOTORS I HAVE IN THE SHOP WILL REPLACE THE ORIGIONAL U2B DEBUTED SPECIAL
HE CAN JUST TURN ON THE LIGHT. AND ITS ALL FREE. I HAVE ONE CONFESSION TO MAKE ABOUT THE ONE IN THE FIRST VIDEO THAT EVERYONE HAS COMPLEMENTED ON FROM THE BEGINNING. THAT IS , THAT THE ONE THAT IS IN THE VIDEO IS THE 7th OR 8th ONE I DID. I DID IT FOR SOMEONE ELSE BUT I DESTROYED ONE OF THE COIL SETS IN IT BY PULLING ON THE WIRES TO HARD WHILE I WAS RETHREADING THE WIRES TO COME OUT THE OTHER SIDE. BUT THE 12 VOLT SYSTEM INSTEAD OF 24 VOLT SYSTEM WILL NOT SLOW THE BLADES DOWN WHEN UNDER A LOAD SO IT PERFORMS AT ITS LOWERED MAXIMUM VOLTAGE MOST OF THE TIME. IT SEEMS TO KEEP MY SHOP RADIO AND FLOURESENT LIGHT GOING AS MUCH AS I NEED IT TO EXCEPT FOR WHEN IT RAINS AND THE WIND DOESNT BLOW FOR A FEW DAYS. ONE OF THE CEILING FAN MOTORS I HAVE IN THE SHOP WILL REPLACE THE ORIGIONAL U2B DEBUTED SPECIALWITH MORE MAGNETS AND TWICE THE COILS FOR MORE OUTPUT. THE BLACK ONE IS CRANKING OUT 5 TIMES THE POWER ALREADY, IM JELOUS. AND IT COGS REAL HARD. AND WHEN YOU SHORT THE WIRES IT GETS REAL HARD TO TURN. THAT IS A GOOD TEST OF EFFICIENCY. ANY DC OR AC PERMANENT MAGNET MOTOR THAT YOU CAN SHORT THE WIRES OUT ON AND IT DOESNT WANT TO TURN IS A DARNED GOOD WIND TURBINE. IF WE ADD ANOTHER SET OF MAGNETS TO HIS IT WILL DUOBLE THE VOLTAGE AND WE WILL HAVE TO GO TO A HIGHER VOLTAGE BATTERY BANK WHICH IS GOOD SEEING AS THE COILS CAN ONLY PUT OUT 1 AMP PER SET. THERE ARE 2 SETS SO 2 AMP TIMES 48 VOLTS = 100 WATTS SO IF WE ADD THE MAGS IT WILL BE A 200 WATT UNIT WITHOUT HEATING UP THE WIRES BUT WE WILL HAVE TO GET 7 OR 8 BATTERIES. OR AT LEAST 4 OR 5 . TIME WILL TELL. MUDD
Q: How much do you charge to build and ship one?
What type of glue you used for the strap metal?
Ans: 2 PLACE ANOTHER STRONG MAGNET TO THE FRONT OF THE MAGNET RIGHT AWAY, AND LET THEM COOL. THE MAGNETIC FLUX WILL BE REPLACED. THUS YOU CAN ALSO SWAP THE POLARITY IF NEED BE. GET THE MAGNETS AS CLOSE TO THE STATOR AS POSSIBLE WITHOUT TOUCHING THE STATOR. KEEP THE WEIGHT BALANCED.
MUDDy
Q: If you can pick up old microwave ovens, on the high voltage side there is 1 diode which is rather big and can reliably take a good amount of power. Old microwaves can often be obtained for free on freecycle, or ask a local appliance dealer. They are also a treasure trove of other handy bits, and if your really good with metals you might even be able to make the banding from the case.
Ans: I CUT SOME GLASS MIRROR INTO 1 INCH SQUARES, AND JUST EPOXIED THE SQUARES TO THE MICROWAVE SATELLITE
DISH AS TIGHT AS POSSIBLE. REMOVE THE LMB ANTENNA, AND YOU ARE SET. CUT LENGTHS OF COAT HANGER WITH A CURL AT ONE END. THREAD THE HOT DOG ON THE WIRE, AND HOLD THE WIRE BY THE STRAIGHT END, AND SPIN IT IN THE BRIGHT SPOT. USE WELDING GLASS TO WATCH WHAT YOU ARE DOING.
FAST AND EASY.
DISH AS TIGHT AS POSSIBLE. REMOVE THE LMB ANTENNA, AND YOU ARE SET. CUT LENGTHS OF COAT HANGER WITH A CURL AT ONE END. THREAD THE HOT DOG ON THE WIRE, AND HOLD THE WIRE BY THE STRAIGHT END, AND SPIN IT IN THE BRIGHT SPOT. USE WELDING GLASS TO WATCH WHAT YOU ARE DOING.
FAST AND EASY.
0 comments
Write Down Your Responses